• <var id="3ipty"></var> <source id="3ipty"></source>

    1. <u id="3ipty"><sub id="3ipty"></sub></u>

      Products

      Hydroxyethyl cellulose(HEC). Possesses trustworthy properties in respects of thickness promotion, enulsification, suspension, dispersion, cohesion, moisture-keeping and anti-microbic fuction etc.  Sanyou Chemical Co.,Ltd is at present the largest HEC production base at home, the corporation can provide surface-treated and untreated TF-series, different kinds of HEC with various viscosities, which finds wide applicalions in suspension polystyrene, foamable polystyrene, emulsion and new-type acrylic resin emulsion paint, colorful paint, ion exchange resin, daily-use chemicals and such departments as well drilling in oil fields, building materical, textile, printing and dyeing and mintage machining etc. providing good properties inf thickness promotion, emulsification, suspension, dispersion, moisture-keeping and anti-microbic function etc.
      Chemical property of HEC
             HEC consists of two parts, one is cellulose, the other is hydroxyethyl side chain, HEC itself does not dissolve in water and is composed of numerous monose units, as illrstrated in figure(1), reaction of purified cellulose with sodium hydroxide produces alkaline cellulose colloids, put epoxyethane ito the colloide, HEC can be obtained. Since a monose unit of cellulose contains 3 hydroxies, the maximum replacement value should be 3. Nowaday, the replacement value of HEC is controlled between 1 and 2 on average, at the same time, the applied amount of epoxyethane is also controlled at 2 grammoles versus a monose unit, that is to say, on average one monose unit reacts with 2grammoles of epoxyethane, which may be joined togegher, a head with another’s tail, and then connected to a hydoxy or to two hydroxides respectively, as illustrated in figure(2)Fig(1):the structural drawing of collulose.
      Fig(2):the standard structural duawing of HEC

       Quality index of HEC
             As stated above, HEC is non-ion water-soluble polymer and can tade active effect on thickness-promotion, emulsification, dispersion, stabiliztion, moisture-keeping, film-forming and thus providing protective colloids. HEC is very easy to dissolve in both hot and cold water, viscosity of the solution may vary within a wide range, and high density of elec-trolyte is also acceptable.Fig(1).Quality index of HEC
      specifictionbrand No Appe-arance Gram-mole repla-
      cement
      value (m·s)
      mois-ture(%) indiss-
      olubility
      (%)
      Pervio-usness of light(2%) NDJ-1 rotary viscometer mPa.s 2% 20℃ water solution
      Viscosity range Spindle No. Rotary speed of spindle
      TF-50S powder 1.8-2.0 <6 <0.5 ≥80 <100 1 30
      TF-1000S powder 1.8-2.0 <6 <0.5 ≥80 800-1200 2 12
      TF-6000S powder 1.8-2.0 <6 <0.5 ≥80 4000-7000 3 12
      TF-10000S powder 1.8-2.0 <6 <0.5 ≥80 8000-12000 3 6
      TF-15000S powder 1.8-2.0 <6 <0.5 ≥80 13000-17000 3 6
      TF-20000S powder 1.8-2.0 <6 <0.5 ≥80 18000-24000 4 12
      TF-30000S powder 1.8-2.0 <6 <0.5 ≥80 26000-34000 4 12
      TF-40000S powder 1.8-2.0 <6 <0.5 ≥80 36000-44000 4 12
      TF-60000S powder 1.8-2.0 <6 <0.5 ≥80 55000-65000 4 6
      TF-70000S powder 1.8-2.0 <6 <0.5 ≥80 66000-74000 4 6
      TF-80000S powder 1.8-2.0 <6 <0.5 ≥80 75000-83000 4 6
      Nate: (1)Here the weight of 2% water solution is calculated according to the weight of dried HEC.“S” is attached after the brand No. of the fast soluble product, for example, FT-6000S refers to TF-6000 as a fast soluble product, please make clear when ordering.
      Merit of using HEC made in Wuxi Sanyou Chemical Co.,Ltd.
      1) Easy preperation of solution
      A simply equipped stirrer may be used for HEC to dissolve into hot or cold water, the solution may be put into product directly.(2) Excellent compatibility
      Since HEC is non-ion chemical, therefore may be used safely while PH value is ranging from 2 to 12, and can present excellent compatibility with other compositional materials such as pigments, additives, salts or electrolytes.(3) Easy operation
      Product prepared with HEC is pseudoplastic, therefors possesses excellent evenness while applied, without dropping or waving on surface.(4) Very good film-forming
      Since surface tension of product will not be reduced, therefore unnecessary foams will not emerge in production prodcess, at the same time, small holes and needle-like holes will not engender from foams.(5) Stable color
      HEC is able to cooperate with various pigmints and solvents in the formulas and make the color more bright and more harmonious.(6) Longer storage period
      HEC makes color liquor more stable, thus prolongs storage period, decreases color gradation and separation, and furthermore keeps viscosity stable while timperature varying greatly up and down.
      Directions for the use of HEC
       Nowadays, three methods are taken as general use.Method A:
      Putting in on production directly, the method is most simple and short time is meeded, the precedure is as follows.1. Pour clear water into a big tub fitted with high pressure stirrer
      2. At first, keep stiring slowly, then gradually and equally sieve HEC into solution
      3. Do not stop stirring until all the granules are fully wetted.
      4. Add antimildews and various additives such as pigment dispersing agent, ammonia water etc.
      5. Do not put other ingredients of concerned formula and preceed to chemical reaction until all the HEC is thoroughly dissolved (viscosity of the solution is obviously increased)Method B:
      Prepare mother liquor for use.
      The method is to prepare in advance high density mother liquor, then put it in product. Advantage of the method consists in flexibility, the liquor may be put in product directly, but suitable storage is needed. The procedure is similar to the steps (1)~(4) of the method A, the difference is no need of high pressure stirrer, only such a stirrer is needed as has enough power to keep HEC equally dispersing in solution. And stirring till entirely dissoled into viscouse solution. Please note antimildews must be put into the mother liquor as early as possible.Method C:
      Compounding into gruel-like substance for use
      Since organic solvents are poor solvents for HEC, therefore these solvents may be used to pripare the gruel-like substance, the most often used organic solvents are ethylene glycol, propyl glycol and filming agent (such as adipic glycol or buty1 carbitol acetate). Ice water is also a poor solvent and hence also often used with organic liquid to prepare the gruel-like substance.The gruel-like HEC may be directly put into product. HEC in gruel-like state has be fully soaked and swelled, when put into product, it dissolves immediately and takes thickness-promotion effect. After putting into,stirring should still be kept until completely dissolved. Usually, the gruel-like substance is a compound of 6 portions of organic solvent and 1 portion of HEC, when compounded for 6-30 minutes, HEC will hydrolyze and swell evidently. Insummer, the water temprature is too high to compound the gruel-like substance.
      Points for attention while preparing HEC mother liquor
      The surface-treated HEC takes on powder state or fibreshaped solid state, if only pay attention to following matters, the operation will be easy for HEC to dissolve in water.(1) Before and after HEC is put in, unceasingly stirring is needed, until the solution becomes clear enough and completely clarified.(2) Do sieve HEC slowly into the tub, do not directly put large amount of or lumpshaped and ball-shaped HEC into the tub.(3) HEC solubility has much to do with water temperature and its PH value, special attention should be paid to, please see figure(3) and figure (4) for reference.(5) Put in antimildew beforehand as possible as you can.(6) When high density HEC is used, the density of mother liquid should not be higher than 2.5-3%(according to weight), otherwise the mother lequor will be difficult to operate.The aftertreated HEC usually does not conglomerate easily and will not form undissolved ball-shaped colloids after put into water.Figure (3), Relation between dissolution (hydrolysis) speed of TF series HEC and PH value 2% water solution at 25 ℃Rotary viscometer, model NDJ-1

      Figure(3), Relarion between dissolution (hydrolysis) speed of TF series HEC and PH value
      2% water solution at 25℃
      rotary viscometer, model NDJ-1
      after becoming gruel-like
      PH value increases to 9 or 10
      Ordinary water
      PH8
      Stramed water
      PH7
      Reading (viscosity)
      Figure(4) Relation time(minutes) between dissolution (hydrolysis) speed of TF series HEC and temperature
      2% water solution
      rotary viscometer, model NDJ, 100rpm
      At 50Ё, prepare the gruel-like, them increase PH value to 9, put in antimildew, other alkaline ingredients of aqueous ammonia
      Reading
      (viscosity)
      time (hours)
      Figure (4) Relation between dissolution (hydrolysis) speed of TF series HEC and temperature
      2% water slution
      rotary viscometer, model NDJ,100rpm.

       Properties of HEC and its packing
       The basic properties are listed in the following table.
        Item Index
      1 appearance White, light yellow, fibre or powder, solid state.
      2 Surface density  g/ml 0.35~0.61
      3 Specific gravity (film 20%/20℃) 1.38~1.41
      4 dioptre(film n.20) 1.51
      5 Softening temperature ℃   135 ~140
      6 Decomposing temperatu ℃ 205~210
      7 Combustion speed slow
      8 Grammole replacement value 1~2
      9 Viscosity(2%、20℃、mPa.s) tens to ten thousands
      10 volatility(w/w) ≤ 5%
      11 ash(according to Na2CO3) ≤ 6%
      12 PH 6~7
      13 Density(g/ml) 0.55~0.75
      14 Granule size Mesh No40,sieved-through rae≥90%
      15 Surface tension(0.01~0.1% )Water solution,25 ℃ 60~65  dynets/cm
      16 Static electricity no
      17 dissolubility Soluble in cold, hot water, acid, alkaly;insoluble in most organic solvents.
      Moisture regain:
      All models of HEC are absorbent of moisture, moisture held in the ex-factory product is generally controlled below 5%, but environment in trasportation and storage varies, and the moisture held in the prouct increases. When the product is used, measure the moisture, and deduct the moisture weight, do not expose it to the weather.The powder dusts are explosive
      Like all the organic powder dusts density in the air reaches certain degree and ignited . Operate properly, do your best bo avoid gendering power dusts.Packing
      Packages are two kinds: the simple and the fine.
      (1) The simple package is high-pressure polyethylene outside.
      (2) The fine package is high-pressure polyethylene polythene inside and corrugated catron drum out side
      (3) Net weight 20kg each.
      Transport:
      As common moisture-tight chemicals
       Reference-the application of HEC in emulsion paint
      1. Formulas for reference.(1) High-quality outdoor emulsion paint(code E-1420). Pure acrylic emulsion paint and denatured alkyd resin emulsion paint are the major.
      PIGMENT LIQUOR INGREDIENTS Pure acrylic acid emulsion paint Denatured alkyd resin emulsion paint
      Weight(pound) Volume(gallon) Weight(pound) Volume(gallon)
      water 277.0 33.3 227.0 33.3
      HEC TF-15000S 4.6 0.4 4.6 0.4
      Foam eliminant 1.0 0.1 1.0 0.1
      Dispersing agent 8.5 0.9 8.5 0.9
      KTTP 1.0 / 1.0 /
      Ethylene glycol 25.0 2.7 25.0 2.7
      Antiseptic agent 2.0 0.2 2.0 0.2
      TERGITOL NP-10 2.5 0.3 2.5 0.3
      Zinc oxide 50.0 1.1 50.0 1.1
      Titanium white 225.0 6.5 225.0 6.5
      clay 150.0 7.0 150.0 7.0
      Other INGREDIENTS
      activator / / 20 0.2
      Alkyd resin(treated with drier) / / 27.4 3.3
      UCAR acrylic acid emulsion 515 410.0 44.9 348.0 38.0
      water / / 32.5 3.9
      Buty1 Carbitol 15.0 1.9 13.0 1.6
      Mildewcide 2.0 0.2 2.0 0.2
      28% ammonia water 3.0 0.4 2.0 0.2
      Foam eliminant 1.0 0.1 1.0 0.1
      total 1177.6 100.0 1174.5 100.0
      Properties of emulsion paint product
      composition Pure acrylic emulsion paint Denatured alkyd resin emulsion paint
      Pigment velume concentration(PVC) 10% 40%
      Denatured amount of alkyd resin 0% 15%
      Solid content(according to volume) 36.5% 36.5%
      (According to weight) 54.5% 54.2%
      PH 9.0 9.0
      Viscosity Stormer reading 85KU 95KU
      Viscosity Brusnometer reading 1.1泊 1.0泊
      (2) Indoor emulsion paint (code:l-1258)Ethylence and acrylic acid emulsion paints are the major
      composition Weight(pound) Volume(gallon)
      water 400.0 48.2
      HEC TF-6000S 5.0 0.4
      Dispersing agent 6.0 0.7
      TERGITOL XP-10 2.0 0.2
      Ethylene glycol 15.0 1.6
      Buty1 Carbitol acetatef 10.0 1.3
      Foam eliminant 4.0 0.5
      Antiseptic agent 0.5  
      Titanium white 250.0 7.1
      Calcium carbonate(rutile) 125.0 5.5
      Clay 75.0 3.5
      Porcelain clay 50.0 2.1
      UCAR 366 ethyleneand acrylic acid emulsion 260.0 28.9
      Tatol 1202.5 100.0
      Properties of the emulsion paint
      Pigment volume concentration(PVC) 55%
      Solid content(weight) 54%
      Veight for a gallon 12 pounds
      Viscosity (Stormer) 85-88KU
      (3) Indoor high-lustre emulsion paint(code:l-1413A)Acrylic acid emulsion and ethylene-acrylic acid emulsion are the major.
      Pigment liguor INGREDIENTS Weight(pound) Volume (gallon)
      water 150.0 18.01
      Polypropylene glycol 40.0 4.63
      HEC  TF-15000S 2.5 0.23
      Dispersing agent 9.0 0.97
      Butyl carbitol acetate 25.0 3.15
      Foam eliminant 1.0 0.13
      Tergitol NP-40 4.0 0.40
      Antiseptic agent 1.0 0.13
      Titanium white 250.0 7.27
      water 50.0 6.00
      Moistening agenmt 2.0 0.24
      UCAR 503 acrylic acid emulsion 420.0 45.67
      Foam eliminant 1.5 0.20
      Water or concocted water with thickness-promoting agent 104.0 12.50
      28% ammonia water 3.6 0.45
      total 1063.6 99.98
      Properties of emulsion paint
      Pigment volume concentration(PVC) 23.0%
      Solid content, according to volume 31.6%
      Solid content, according to weight 46.6%
      Weight per gallon 10.6磅
      Viscosity (Stormer) 85.0K
      Film luster, angle 600 85
      2. Guide to selecting viscosity model of HEC
      Type of EP (emulsion paint) Brand code of viscosity Main function in paint
      Low price EP TF-40000S
      TF-30000S
      Less thichness-promoting agent, low cost
      Common indoor EP TF-6000S
      TF-10000S
      TF-15000S
      Balande each property of paint such as evenness, stability, color,antiattrition, suspension flowage etc.
      Common outdoor EP TF-6000S
      TF-10000S
      TF-15000S
      Good stability, keeping pigment in suspension, resistence to rain
      Omni-lustre or semi-luster EP TF-6000S
      TF-10000S
      TF-15000S
      Good evenness
      Embossing EP TF-15000S
      TF-30000S
      Froming stable bigger colloid granules.
      3. Factors effecting the viscosity of emulsion paint.(1) The more the residual air bubbles in paint, the higher the viscosity.(2) Suitable amount of surface activator versus water.(3) Residual oxide quantity such as catalyst while compounding emulsion.(4) Proportion of other natural thickness promoter to HEC.(5) Appropriate procedure putting in thickness promoter.(6) Excessive stirring sets off overheat while dispersing.(7) Microoganism erosion on thickness promoter.For details of above-mentioned factors please apply to our corporation.4. Another important application of HEC in respect of emulsion-protective colloid of emulsion polymerization.Apart form being served as stable thickness promoter, HEC also plays an important role in polymerization of compound emulsion-protective colloid.Good emulsion paint requires a special paint theology to ensure fine evenness and eliminate brush trails on the surface of dried paint film. The theology has to do with the size and distribution of the emulsion granules, yet the size and distribution have a bearing on the stabilizer system and polymerization technology adopted in polymerization.The polymerization caused by using HEC as protective colloids will produce uniform emulsion quality, without difference in different batchtes of emulsion; meanwhile the emulsion granule size may be controlled within a narrow scope and the granules will serve as indispensable materical for the emulsion polymerization.The emulsion polymerizations which usually use HEC as the protective colloid include;Vinyl acetate and other copolymerizing monomers such as acrylic resin, butadiene resin; para-butadiene resin, ethylene etc. methyl acrylic resin and other coplymerizing monomers such as acrylate, butadiene etc.Styrene-acrylate copolymer, styrene-butadiene coplymer, vinyl chloride-acrylate copolymer, acrylonitrile-butadiene copolymer.For detail techmological data please apply to Wuxi SanyouChemical Co.,Ltd.The aforesaid data and recommended formulas are drawn up on the basis of the manual of the USA United Carbon Chemical Company (UCC) and only for your reference.
         
      COPYRIGHT©2010 www.waophotography.com    Wuxi Sanyou New Material Technology Co., Ltd.  Add: Nancao(Caoqiao), Yixing, Jiangsu, China.    P.C: 214217    TOP
      TEL: +86-510-87851046、87853668、87852066    FAX: +86-510-87851046、87851139 久久无码视频131_91一区二区三区在线_国产精品无码A∨麻豆_国产精品农村妇女α片
    1. <var id="3ipty"></var> <source id="3ipty"></source>

      1. <u id="3ipty"><sub id="3ipty"></sub></u>